Fix ReSkate multiplayer: the Unknown Player bug, Multiplayer is off on Deck, version mismatches and Proton join failures, with the exact order to test them.
ReSkate Multiplayer Not Working: Fixes That Work
Official source: ReSkate releases and skate. on Steam
Most ReSkate multiplayer failures come down to one of four causes: Steam is not signed in, the host's server is not reachable, the two players are on different game builds, or you are on Proton and hit a known Linux issue. Work through them in that order. Each check takes under a minute, and the first one explains the majority of reports.
The symptom that gives it away is the name. If ReSkate shows you as Unknown Player, the Steam handoff failed, and multiplayer is disabled as a consequence rather than as a separate bug.
Version-sensitive facts are stamped as of v1.1.3, 2026-10-07. This site is unofficial and unaffiliated with EA, Full Circle or Dingo-Shenanigans.

Pictured: a working ReSkate session, the state these fixes are trying to reach.
Unknown Player means the Steam handoff failed, and multiplayer stays off until it is fixed.
Fix 1: sign into Steam first
ReSkate authenticates through the Steam client. If Steam is not running, or is running but signed out, the platform cannot read your identity and falls back to Unknown Player.
- Start Steam and confirm you are signed in, not in offline mode.
- Launch ReSkate from the launcher while Steam is running.
- Check the name in the ReSkate overlay before joining anything.
If the name is still Unknown Player, close both Steam and the game completely, then relaunch Steam first and ReSkate second. Launching the game before Steam is the single most common ordering mistake.
Fix 2: confirm the host is actually hosting
A ReSkate session needs a host. If nobody is hosting, "multiplayer not working" is really "no server".
| Setup | Who hosts | What to check |
|---|---|---|
| Steam lobby | One player in-game | The host has started a session, not just launched |
| Dedicated server | A separate process or machine | The server console shows the port bound |
| Community server | Someone else | The address and port are current |
The server setup guide walks through hosting, and the multiplayer page covers the lobby sizes: 32 players through the Steam lobby, with community servers running far larger.
Fix 3: match the game build
ReSkate locks to a specific skate. build - build 25414733 since v1.0.0. If one player's skate. has updated past the supported build and another has not, the session will not form even though both launch fine.
Check the build in Steam: right-click skate., Properties, Betas, and confirm neither player is on a beta branch. Then confirm both players run the same ReSkate version from the launcher's about screen. Mixing v1.1.2 and v1.1.3 is a common cause after an update.
Fix 4: Proton and Linux
Proton works, but the project has a documented history of multiplayer issues on Linux:
- Joining servers under Proton was fixed in v1.0.9 (issue #28). If you are on an older build, update.
- Hosting from a Steam Deck can report "Multiplayer is off" (issue #19). Playing on a Deck and joining someone else's server is more reliable than hosting.
- Custom maps and modded servers can hang on load under Proton (issue #31). Test with vanilla maps first.
If you are on Linux, confirm your Proton version and test joining a vanilla server before assuming the platform is broken. The Deck and Linux guide has the version notes.
Fix 5: firewalls and ports
A host behind a strict firewall will accept the lobby but never receive the connection. Windows Defender prompts on first host; if you dismissed it, the rule is missing.
- Open Windows Security, Firewall and network protection, Allow an app through firewall.
- Find ReSkate and skate., and enable both Private and Public.
- If you host a dedicated server, forward its port on the router, not just in Windows.
Port numbers and configuration keys are in the server configuration page.
Fix 6: mods that disagree
Mods that change maps, physics or vehicle handling must match between host and client. A host running a custom park and a client without it will either fail to load or drop on join.
The quickest test is to disable all mods on both sides, confirm the session works, then re-enable them one at a time. The mod compatibility page lists which categories are client-side and which must match.
The diagnostic order
| Order | Check | Time |
|---|---|---|
| 1 | Steam signed in, launched first | 30 seconds |
| 2 | Name is not Unknown Player | 10 seconds |
| 3 | Host has started a session | 1 minute |
| 4 | Both on build 25414733 and the same ReSkate version | 2 minutes |
| 5 | Firewall rule exists for host | 1 minute |
| 6 | Vanilla mod list on both sides | 5 minutes |
| 7 | Proton-specific issues, if on Linux | 10 minutes |
Nine times out of ten the answer is in the first three rows. The community install walkthrough at skatemods.com shows the Steam handoff in screenshots if the ordering is unclear.
When it is not your fault
If the session list is empty for everyone, the lobby backend or the community server is down, and nothing on your machine will fix it. Check the project's issue tracker and Discord before reinstalling anything. Reinstalling is the most common wasted hour in troubleshooting, because the failure is almost never in the client files.
If the game crashes on join rather than failing silently, that is a different problem: the errors page covers crash paths, and the install walkthrough covers a corrupted install.
FAQ
Why does ReSkate say Unknown Player? Steam was not running or not signed in when the game launched. Start Steam first, then ReSkate.
Why is multiplayer off on my Steam Deck? A known hosting issue under Proton (issue #19). Joining a server usually works even when hosting does not.
Do both players need the same mods? Only mods that affect maps, physics or handling. Cosmetic client-side mods can differ.
Does ReSkate support crossplay with consoles? No. There is no console version of ReSkate, and skate. does not share servers with it.
How many players can join? 32 through the Steam lobby, with community servers configured for more.
Is there a server browser? Sessions are joined through the platform's server list and direct address entry, covered on the multiplayer page.
Related
More ReSkate Guides
Every ReSkate update from v1.0.0 to v1.1.3: per-version changes, pinned game build record, and how the launcher self-updates.
How characters work in ReSkate: your own skater, locally saved outfits and unlocks, Unknown Player when Steam is offline, and costume mods.
Official ReSkate Discord, GitHub, Thunderstore and Reddit links in one place: community hubs for new players, as of v1.1.3.
ReSkate keys and console commands cheat sheet: Insert menu, T chat, ~ console help; key changes follow the version stamp.
What changes in ReSkate gameplay: pinned skate. physics, offline play, 32-player lobbies, throwdowns, world controls, park editor and plugin modes.
Where ReSkate official code, releases and issue tracker live, how to read each repository, and how to confirm a download is genuine before running it.
Hall of Meat is a ReSkate plugin mod now, not a console toggle. How to install it, approve permissions, enable it in a session and fix the old command.
How to play ReSkate from first launch: get online properly, learn the three keys, try lobbies, parks, Hall of Meat and the Trainer, then add your first mods.
